Start with the Fuji fit and what the i40 gives you
The Nissin i40 Flashgun is a compact, lightweight option for Fuji cameras, weighing just 203g. It supports Fuji TTL, so you can use automatic flash exposure without manually calculating output. The flash also offers high-speed sync up to 1/8000th second, a rotating head for bounce, an LED video light with 9 output steps, and a built-in diffuser for 16mm lens coverage. A soft box is included to soften output and reduce shadows.
This guide walks through the practical setup steps for Fuji cameras, from mounting the flash to using TTL, high-speed sync, bounce and manual mode. It also covers what to check if you buy the B-Stock version.
Key i40 specs for Fuji shooters
- (B-Stock) Nissin i40 Flashgun - Fuji Fit: Supports Fuji TTL flash exposure. Fuji TTL lets the camera and flash communicate automatically, so you can focus on composition instead of flash calculations.

(B-Stock) Nissin i40 Flashgun - Fuji Fit - (B-Stock) Nissin i40 Flashgun - Fuji Fit: High-speed sync supports shutter speeds up to 1/8000th second. Useful for wide-aperture outdoor portraits where you want to balance flash with bright ambient light.
- (B-Stock) Nissin i40 Flashgun - Fuji Fit: Flash head rotates 180 degrees left and right and tilts up 90 degrees. Enables bounce flash off walls and ceilings for softer, more natural light.
- (B-Stock) Nissin i40 Flashgun - Fuji Fit: Weighs 203g and includes a soft box. A light, travel-friendly kit that softens light without adding much bulk.
Mounting and powering the i40 on a Fuji camera
The i40 has a metal hot shoe with a quick-release button, making it easy to attach and remove. Slide the flash onto your Fuji camera's hot shoe until it clicks, then tighten the locking ring if present. The supplied information does not detail specific battery requirements, so check the flash's battery compartment or manual for the correct batteries.
- Attach the flash: Slide the i40's metal hot shoe onto your Fuji camera's hot shoe and secure it with the quick-release button.
- Insert batteries: The catalog does not specify battery type or quantity; refer to the flash manual or battery compartment markings.
- Power on: Turn on the flash and the camera. The i40 should be recognized; if not, check that the flash is fully seated and the camera's flash settings are enabled.
Using Fuji TTL for automatic flash exposure
Once mounted, set the i40 to TTL mode using the function dial. The flash will communicate with your Fuji camera to adjust output automatically. This is the simplest way to get balanced flash exposure, especially when moving between different lighting conditions. Use the power dial to adjust flash exposure compensation if needed; the indicated lamp A/B/C shows the adjustment position.
TTL is a good starting point for events, family photos and travel. If you want more control, switch to manual mode as described later.
High-speed sync for bright conditions
The i40 supports high-speed sync (HSS) up to 1/8000th second. This lets you use flash with wide apertures in bright daylight, avoiding the shutter speed limit that normally applies to flash. To use HSS, enable it on the flash and set your camera to a compatible shutter speed. The supplied information does not list specific Fuji models that support HSS, so test with your camera to confirm compatibility.
Bounce flash for softer light
The flash head rotates 180 degrees horizontally and tilts up 90 degrees. For softer, more natural light, point the head at a nearby wall or ceiling and let the light bounce back onto your subject. This reduces harsh shadows and gives a more flattering look. The included soft box can be added for further diffusion, especially when bouncing isn't possible.
When bouncing, keep in mind that the light picks up the color of the surface. White or neutral surfaces give the most accurate color.
Manual mode tips for predictable results
In manual mode, you set the flash output yourself using the power dial. This is useful when you need consistent exposure across a series of shots, or when TTL struggles with difficult lighting. Start with a moderate output and adjust based on your histogram or test shots. The i40's selector dial and function dial make it easy to change settings quickly.
Manual mode also works well with the LED video light, which has 9 steps of output adjustment. You can use the video light for constant lighting while framing, then switch to flash for the exposure.
B-Stock considerations
This i40 is offered as B-Stock, which means it may be ex-demo, come without branded packaging, or show minor aesthetic imperfections. Functionally, it should perform as expected, but if you have concerns about condition, contact Kenro sales before ordering. The B-Stock price is lower than the comparison price, making it a cost-effective way to add a compact Fuji-fit flash to your kit.


